Industrial 3D Scanning

See how industrial-grade 3D scanners are used for production inspection, first-article checks, quality control, and complex part measurement.

When Freeform Surfaces Defeat Conventional Measurement

2026/07/10

When Freeform Surfaces Defeat Conventional Measurement

A freeform surface is not a defect. It is a deliberate design choice that appears in turbine blades, orthopedic implants, automotive body panels, and consumer e
3D Scanning Inspection Report

2026/07/10

3D Scanning Inspection Report

A 3D scanning inspection report is a standardized, structured output document generated from industrial 3D metrology workflows that quantitatively and visually documents the geometric conformance of a physical test part against a predefined reference.
From Scan Data to Inspection Reports: 3D inspection of mechanical components in Practice

2026/07/10

From Scan Data to Inspection Reports: 3D inspection of mechanical components in Practice

Mechanical components rarely arrive at the inspection station in a textbook-ready state. A sand-cast gearbox housing fresh from the foundry carries a pebbled su
Why Mold-Corner Inspection Fails Before It Even Starts

2026/07/09

Why Mold-Corner Inspection Fails Before It Even Starts

Injection mold cavities, blow mold pinch-offs, and deep draw tooling carry a predictable headache: the geometry that matters most for part quality sits where no
3D Scanning Point Spacing

2026/07/09

3D Scanning Point Spacing

3D scanning point spacing, also referred to as point pitch or point distance, is the linear distance between adjacent discrete 3D coordinate points in a point cloud generated by a 3D scanning system.
When Narrow Gaps Defeat Standard Inspection Tools

2026/07/09

When Narrow Gaps Defeat Standard Inspection Tools

A turbine disk with cooling channels no wider than a fingernail. A fuel injector body where the critical sealing surface sits 60 mm below the entry face. An add
Precision That Curves With the Pipe: Rethinking Weld Inspection on Cylindrical Surfaces

2026/07/08

Precision That Curves With the Pipe: Rethinking Weld Inspection on Cylindrical Surfaces

A pipe weld is never just a weld. It sits on a curved, often thick-walled cylinder, wrapped in mill scale, heat tint, or a thin layer of shop primer. The joint
Overcoming Distortion in Large Welded Fabrications: A 3D Scanning Strategy for Heavy Structures

2026/07/08

Overcoming Distortion in Large Welded Fabrications: A 3D Scanning Strategy for Heavy Structures

The geometry of a large welded structure rarely matches the design intent exactly. Even with controlled welding procedures, heat input causes localized expansio
3D Scanning Repeatability

2026/07/08

3D Scanning Repeatability

3D scanning repeatability is a metrological performance metric that quantifies the degree of consistency between 3D measurement results obtained when scanning the same object or reference artifact across multiple consecutive trials, under identical operating conditions.
When Castings Push Inspection Limits: Rethinking Dimensional Control with 3D Scanning

2026/07/07

When Castings Push Inspection Limits: Rethinking Dimensional Control with 3D Scanning

Castings are the foundation of industrial machinery, from pump housings and valve bodies to engine blocks and large structural components. Their geometry is rar
From Part Geometry to Inspection Reports: 3D scanning for automotive body panels

2026/07/07

From Part Geometry to Inspection Reports: 3D scanning for automotive body panels

A body panel that looks right on the assembly jig can still produce a fender-to-door gap that flags under a 2.5 mm gauge, sends a hood leading edge too high, or
Sources of Error in 3D Scanning

2026/07/07

Sources of Error in 3D Scanning

Sources of error in 3D scanning refer to the full set of systematic, random, environmental, workflow-related, or material-based factors that introduce measurable deviation between the 3D point cloud, mesh, or measurement output of a 3D scanning system and the true geometric dimensions of the physical object being scanned.